







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Metal Roofing in Sunnyvale, TX: What It Costs and How It’s Done
Metal roofing in Sunnyvale, TX typically runs $15,000 to $40,000 installed, and a standard single-family roof takes about five to nine working days from tear-off to final inspection. The number lands in that band depending on roof size, panel type, and how much decking and trim the job needs. On the acreage properties east of town, with their big spans and detached shops, metal is often the finish that makes the most sense for the long haul. Call (888) 426-8078 for a free on-site estimate and we’ll put real numbers to your roof.
Key takeaways
- Installed cost in Sunnyvale: $15,000 to $40,000, driven mostly by roof square footage and panel type.
- A typical re-roof takes five to nine working days, weather permitting.
- Metal handles North Texas hail and wind better than most alternatives, and on a big custom-home roof the long-term math beats asphalt shingles.
- Permits are pulled through the town’s own permitting office, and that rhythm matters here.
How we install a metal roof, stage by stage

Metal roofing isn’t a one-day slap-on, and we don’t treat it like one. Each stage has a decision that belongs to you, so you know what you’re buying before the crew climbs up.
Stage 1: Tear-off and deck inspection (1 to 2 days)
We strip the old roofing down to the sheathing and walk every panel of decking. On the older custom homes around Sunnyvale, this is where soft spots and past water intrusion show up. You decide whether to repair isolated decking or replace sheathing in full; we price it both ways in writing before anyone commits.
Stage 2: Deck repair and underlayment (1 day)
Any bad decking gets replaced, then we lay a high-temp metal underlayment, not the felt used under shingles. This is the barrier that keeps summer heat from cooking the panels from below and shields against wind-driven rain. You choose the underlayment grade from the written options; we walk you through the trade-off between standard and premium.
Stage 3: Trim, valleys, and flashing (1 to 2 days)
Valleys, eaves, and penetrations get their flashing and trim set before a single panel goes on. These details decide whether the roof stays watertight for decades. We show you where the old failure points were and what we’re doing about them. This is the stage a cut-rate crew rushes, and it’s the stage that haunts a roof later.
Stage 4: Panel install (2 to 4 days)
Panels go on over the deck in runs, screwed and sealed per the manufacturer’s spec. Big roofs take longer; a large custom-home expanse in Sunnyvale can stretch the panel phase. You decide between exposed-fastener panels and a concealed-fastener system, and we can show you samples before install.
Stage 5: Final inspection and cleanup (1 day)
We walk the roof with you, confirm the installation, and pull the permit inspection through the town’s office. Magnets run over the yard for nails, and the site gets cleared. The whole thing is covered by our 730-Day Done Right Promise: if it’s not done right, we make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The metal roof options you’ll actually choose between
Metal roofing is several products under one name, and the choice drives both cost and longevity. Here’s what most Sunnyvale homeowners weigh.
- Standing seam panels: Concealed fasteners, clean vertical lines, and the best weather performance. The top of the range and the best fit for high-end custom homes.
- Exposed-fastener panels (screw-down): Lower cost, faster install, fine for shops and outbuildings. The trade-off is visible fasteners that can back out over decades.
- Stone-coated steel: Gives a tile or shake look while keeping metal’s strength. Good for homeowners who want a traditional profile on a custom home.
- 24-gauge vs. 26-gauge steel: The thicker gauge costs more but dents less under hail. On a hail-prone North Texas roof, thicker is usually the smarter buy.
- Paint and finish: A Kynar-based finish holds color longer than a basic acrylic. It adds cost up front and years of appearance down the road.
Prefab and panelized construction has gotten more common on acreage builds, and products from companies like Dvele and Plant Prefab now show up in the mix. When a homeowner pairs a metal roof with a prefab structure, we plan the flashing and tie-ins to work with the manufacturer’s specs.
What Metal Roofing costs in Sunnyvale, TX

Plan on $15,000 to $40,000 for a full metal roof installed on a Sunnyvale home. The low end fits a modest roof with an exposed-fastener panel; the high end fits a large custom-home roof in standing seam with a premium finish.
Here are the variables that push the number up or down:
- Roof size and complexity: Square footage is the biggest driver. Dormers, hips, and multi-plane custom roofs add labor and waste.
- Panel type: Exposed-fastener panels are the least expensive; standing seam runs highest.
- Gauge and finish: 24-gauge steel and a Kynar finish cost more than 26-gauge with a basic paint.
- Deck condition: Soft or rotted sheathing needs replacement, and that’s labor plus material.
- Trim and penetrations: A roof full of valleys, skylights, and vents takes more flashing and time.
A written estimate from us lists the tear-off, deck repair allowance, underlayment, panels, trim, permit, and cleanup as line items. What it won’t include unless we flag it: structural repairs to framing discovered under the deck, or skylight replacement you add later. No surprise change orders – the number you see is the number you pay.
See the difference
Before
After
Before
After
Before
AfterWhat Sunnyvale’s acreage properties do to a metal roof job
Sunnyvale is a small, affluent town on the eastern edge of Dallas County, ZIP 75182, and the housing stock tells the story: large-lot custom and semi-custom homes plus acreage properties, not dense tract infill. That changes how a metal roof job runs. On the big custom-home roofs out toward the rural edges, we’re measuring fifteen to thirty squares on a single structure, and roofs with steep pitches and multiple planes take more staging and slow the panel phase. The detached shops and barndominium-style outbuildings on those parcels often need their own roof scope, sometimes a simpler exposed-fastener panel that handles the span and budget.
Permitting here is its own rhythm. Because Sunnyvale is small, the town’s permitting and inspection office moves to its own schedule, and we plan the tear-off and inspection windows around it rather than assuming a big-city timeline. It’s a difference homeowners notice when they’ve dealt with permits in Mesquite or Garland. If your metal roof is part of a larger exterior project – say a full Roofing in Sunnyvale scope with gutters and fascia – that coordination matters more.
The climate makes metal a smart pick. Hot, humid summers, heavy spring hail and wind, and the occasional winter ice event all hammer an asphalt roof. Homes are often built alongside shops and accessory structures, and homeowners here frequently pair a metal re-roof with Window Replacement in Sunnyvale to tighten the whole envelope at once, or with Impact Windows & Doors in Sunnyvale for hail-rated glazing to match the roof’s durability.
Serving Sunnyvale, TX – Our Local Coverage Area
We serve Sunnyvale and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked: Metal Roofing in Sunnyvale

Plan on five to nine working days for a typical single-family roof, longer for a large custom-home roof with complex planes. Weather and permit inspection timing can shift the schedule, and we’ll give you a realistic window in the written estimate, not a best-case one. Call (888) 426-8078 to get your roof measured and a timeline set – estimates are free.
Yes. A re-roof in Sunnyvale requires a permit pulled through the town’s permitting office, and the work gets inspected before it’s signed off. We handle the permit and schedule the inspection as part of the job. Call (888) 426-8078 and we’ll walk you through the permitting timeline for your address.
In most cases, yes. A standard metal re-roof goes over the existing deck and framing, so plumbing and interior structure stay untouched. If we find rotted sheathing or framing under the old roof, we price that repair separately and in writing before proceeding. Call (888) 426-8078 for a free estimate that includes a deck inspection.
Metal Roofing in Sunnyvale runs $15,000 to $40,000 installed, with the price driven mostly by roof size, panel type, gauge, finish, and deck condition. Standing seam at the top of the range, exposed-fastener panels at the lower end, with the middle going to stone-coated steel and thicker gauges. Call (888) 426-8078 for an exact quote – estimates are free.
Our installation is covered by the 730-Day Done Right Promise – if it’s not done right, we make it right – on top of the panel manufacturer’s material warranty, which we’ll explain in writing. The two together give you coverage on both the workmanship and the product. Call (888) 426-8078 to review the warranty details for the panel you’re considering.
Get a free metal roofing estimate in Sunnyvale
We come out, measure your roof, inspect the deck, and hand you a written line-item estimate with real numbers and a realistic timeline. No pressure, no vague bids. Every metal roof we install is backed by our 730-Day Done Right Promise, and our technicians bring up to 12 years of experience to the job. Call (888) 426-8078 to schedule your free estimate – a live person answers, and we’re glad to talk through your Roofing options across Sunnyvale whenever you’re ready.
Written by the team at Groundwork Construction Co.












