







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Metal Roofing in Mesquite, TX: What the Job Actually Involves
A metal roof on a typical Mesquite ranch home runs $15,000 – $40,000, and most jobs take two to four days from tear-off to final walkthrough. You’re getting a standing-seam or exposed-fastener panel system installed over new underlayment and decking repairs, with a life expectancy of 40 to 70 years depending on which system you pick. Call (888) 426-8078 to schedule a free on-site estimate and get a written, line-item number before any work starts.
Metal is a different animal from the asphalt shingles on most of the roofs around here. The panels are lighter per square than a layer of architectural shingles, they shed hail far better, and they don’t rot or grow algae the way older three-tab roofs do. That matters when you’re planning to stay in the house another 20 years.
How a Metal Roofing Job Moves From Day One to Done

Every job is sequenced, and you’ll know what’s happening at each stage before we start. Here’s the real order of operations for a metal roofing replacement on a Mesquite home.
Stage 1: Inspection, measurements, and the material order (Day 1, half a day)
We walk the roof, check the decking, photograph any soft spots, and confirm the panel layout so the seams land where they should. You’ll choose your panel profile and color from physical samples at this stage, because the panels are roll-formed to the exact roof dimensions and that order is what triggers the lead time. Panel fabrication is usually 2 to 3 weeks out, so this stage locks your timeline.
Stage 2: Tear-off and decking repair (Day 1 of the install, 4 to 6 hours)
The old shingles come off, along with the old underlayment and any failed flashing around the chimney and penetrations. On a 50-year-old Mesquite ranch, we almost always find a few sheets of rotted decking near the valleys or the plumbing boots. You’ll get a photo of each bad sheet and a price before we replace it. No surprises tacked onto the invoice later.
Stage 3: Underlayment and flashing (Day 2, 3 to 4 hours)
Synthetic underlayment goes down over the repaired deck, then we install the eave trim, valley metal, and the flashing around every penetration. This is the stage that decides whether the roof stays dry, and it’s the stage most rushed crews skip through too fast. Underlayment is not the place to save money.
Stage 4: Panel installation (Day 2 and Day 3, 2 days on a standard ranch)
The panels get set, aligned, and fastened following the manufacturer’s wind-uplift spec, which matters in a hail and high-wind market like Mesquite. Standing seam panels are mechanically seamed at the joints, so there are no exposed fasteners along the field of the roof. Exposed-fastener panels go down faster and cost less, but the screws carry gaskets that need checking every few years.
Stage 5: Ridge, trim, cleanup, and final walkthrough (Day 4, half a day)
Ridge caps, gable trim, and the final closure pieces go on, then we run magnets over the lawn and driveway to catch stray fasteners. You walk the roof line with us, we hand over the manufacturer’s warranty paperwork and our own 730-Day Done Right Promise in writing, and we close out the permit inspection. That’s the job.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Metal Roofing Options You’ll Choose Between
Metal roofing isn’t one product. What you pick here drives both the cost and how the roof looks and holds up 30 years from now.
- Standing seam panels: The premium choice. Concealed fasteners, clean vertical lines, and the best wind and hail performance. It costs more up front and takes longer to install, but there’s nothing to leak at a fastener because the fasteners are hidden. Best fit if you’re staying long-term.
- Exposed-fastener (screw-down) panels: The value option. Lower cost per square, faster install, and still a 40-year-plus life. The trade-off is visible screws with rubber gaskets that can dry out and need periodic inspection. Suits a rental or a budget-conscious replacement.
- Panel gauge and coating: A heavier gauge steel panel resists hail dents better than a thin one, and a quality paint system (the kind GAF and CertainTeed put on their metal lines) holds color longer in North Texas sun. Cheaper coatings chalk and fade within a decade here.
- Color and profile: Standing seam comes in a range of factory colors and two seam heights. Dark colors absorb more heat; lighter colors reflect it and run cooler in July. Your HOA may restrict the palette, so check before you fall in love with a color.
- Structural vs. architectural panels: Standard structural panels are the workhorse. Architectural profiles cost more and mimic tile or shake. On a brick-veneer ranch, a low-profile standing seam usually reads cleaner than a busy architectural panel.
We work with GAF and CertainTeed on our roofing lines, so the metal systems we install are backed by manufacturer warranties you can actually file a claim against. Homeowners who replace a roof often pair this with Window Replacement in Mesquite to cut summer heat gain at the same time.
What Metal Roofing Costs in Mesquite, TX

Plan on $15,000 – $40,000 for a full metal roof replacement in Mesquite. That range is wide on purpose, because five variables push a job from the low end to the high end.
- Roof size and pitch: A smaller ranch with a simple gable sits at the low end. A larger home with multiple hips, valleys, and steep sections needs more panels and more labor, which pushes toward the top.
- Decking condition: Solid 50-year-old decking costs nothing extra. Rotted sheathing, which shows up on homes built in the 1950s and 1960s, adds repair cost per sheet.
- Panel type: Exposed-fastener panels run lower; standing seam runs higher. The gap is real, and it buys you concealed fasteners and a longer service life.
- Penetrations and complexity: Chimneys, skylights, and multiple roof planes all require extra flashing detail and labor.
- Permit and inspection scope: Mesquite requires a roofing permit for a full replacement, and the fee scales with job valuation. We pull it and pass the inspection as part of the job.
A written estimate from us includes tear-off, decking repair up to an agreed amount, underlayment, panels, flashing, trim, permit, and cleanup. What it typically doesn’t include: structural repair to rafters if we find rot underneath, and any gutter or fascia work beyond what’s needed to finish the roof line. We line-item those separately so the number you see is the number you pay.
See the difference
Before
After
Before
After
Before
AfterWhat Mesquite Homes Specifically Do to This Job
Mesquite is a built-out, largely post-war inner-ring Dallas suburb, and most of what we do here is replacement rather than new construction. The city has been essentially fully developed since the 1980s, so the work happens on mature housing stock: 1950s-to-1970s single-family ranches and brick-veneer tract homes, many now past 50 years old. That age shows up in the roof deck first. We pull old shingles off and find soft sheathing and worn-out plumbing boots on a regular basis, and we plan for it.
The North Texas climate does the rest. Spring hail and high-wind storms turn Mesquite into a roof-and-siding rebuild market almost overnight, which is exactly why metal holds up better than shingles here. The black clay soil under these homes swells and shrinks between drought and heavy rain, and while that drives foundation movement more than roof work, a shifting foundation can rack the roof structure and open up seams over time. We check for that during the inspection.
The tight infill lots and mature trees in established Mesquite neighborhoods mean limited staging space, so we plan material delivery and dumpster placement around your driveway before install day. Our roofing service covers Mesquite and the surrounding area, and when the roof is part of a full Roofing in Mesquite scope that also touches fascia or gutters, we coordinate the trades together. If you’re hardening the house against storms more broadly, folks often pair a new roof with Impact Windows & Doors in Mesquite.
Serving Mesquite, TX – Our Local Coverage Area
We serve Mesquite and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Metal Roofing in Mesquite

Most metal roofing jobs in Mesquite take two to four days on the roof, plus two to three weeks before that for panel fabrication. The install itself is fast; the lead time is the panel order. Call (888) 426-8078 to get your panel order scheduled and lock in a start date.
Yes, Mesquite requires a roofing permit for a full replacement, and the fee scales with the job valuation. We pull the permit and pass the inspection as part of the job, so you don’t file anything yourself. Call (888) 426-8078 for a free estimate that includes the permit cost.
In almost every case, yes. A metal roof replacement goes over the existing structure, and we don’t touch plumbing or framing unless we find rotted sheathing or rafters, which we price separately with your approval first. Most Mesquite jobs need no structural work at all. Call (888) 426-8078 to schedule your free inspection and estimate.
Metal roofing in Mesquite runs $15,000 – $40,000 for a full replacement, driven by roof size, panel type, decking condition, and complexity. Standing seam sits higher; exposed-fastener panels sit lower. Call (888) 426-8078 for an exact line-item quote, and estimates are free.
You get two layers of coverage: the manufacturer’s warranty on the metal panels and coating (which varies by system and runs decades on a quality panel), plus our 730-Day Done Right Promise on the workmanship. If it’s not done right, we make it right. Call (888) 426-8078 to review the warranty terms on the specific system you’re considering.
Get a Free Metal Roofing Estimate in Mesquite
Call (888) 426-8078 and a live person answers, day or night. We’ll set a time to walk your roof, check the decking, and talk through standing seam versus exposed-fastener panels with real samples in hand. You’ll get a written, line-item estimate with the permit and cleanup included, backed by our 730-Day Done Right Promise and 0% financing for 18 months. No pressure, no vague numbers.
Written by the team at Groundwork Construction Co.












