







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
What Aluminum Fence Installation in Rowlett Actually Involves
An aluminum fence in Rowlett runs $4,000 – $10,000 installed, with most residential jobs landing between $3,500 and $9,000 depending on footage, height, and finish. The work itself takes two to four days on a typical lot: layout and utility locate first, post-setting next, panels and gates last. Call (888) 426-8078 and we’ll set up a free on-site estimate and walk your property line with you.
How We Build an Aluminum Fence in Rowlett, Stage by Stage

Aluminum isn’t wood. There’s no digging, no framing, no staining, and the panels arrive cut and coated from the manufacturer. That changes the schedule and the decisions you’re making. Here’s how a job actually runs.
Stage 1: Walk the line and locate utilities (day 1, morning)
We mark the property boundary against your plat, confirm gate widths, and call in the utility locate before anyone touches a shovel. Locates in 75088 and 75089 usually come back within 48 hours, so we schedule this as early as we can. This is the stage where you decide gate placement, swing direction, and whether you want a double gate for mower or trailer access.
Stage 2: Demo and set posts (day 1 – 2, one to two days)
If an old fence comes out, removal and haul-off happens here. Posts go into concrete footings sized to your soil and drilled to depth, plumbed and braced, then left to cure. On Rowlett’s blackland clay, footings are dug deeper and bell-shaped at the base because that soil swells with rain and shrinks hard in July. Undersized footings are the number-one cause of leaning aluminum fences we get called out to correct.
Stage 3: Run the panels and set the gates (day 3)
Rails and pickets hang on the cured posts, and gates get their hinges, latch, and closer. Panel height is fixed at this point, so any last decision about a taller privacy section or a decorative top rail needs to happen before this stage. Most jobs are fully enclosed by end of day three.
Stage 4: Inspect and touch up (day 4)
We check every post for plumb, every gate for swing, and touch up any factory powder-coat scratches with matching repair paint. If your project is part of a full Fence Installation in Rowlett, this is where we coordinate the driveway and gate approach so nothing gets blocked.
Stage 5: Walkthrough and written handoff
You get a final walk of the line with us, plus the warranty terms in writing under our 730-Day Done Right Promise. If a post shifts or a gate sags, we come back and make it right. That’s the whole point of the promise.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Options You’ll Choose Between on an Aluminum Fence
- Residential vs. industrial grade: Residential picks run 1½” to 2″ square with thinner wall thickness and cost less. Industrial-grade aluminum has heavier posts and rails, holds up better to dogs pushing on it and gates swinging hard, and adds roughly 15 – 25% to the job. Worth it on a corner lot or a home with big dogs.
- Height (4′, 5′, 6′): Most Rowlett HOAs cap front-yard fencing around 4′ and allow 6′ in the backyard. Confirm your HOA maximum before we order panels, since height drives both material cost and the look of the line.
- Finish and color: Powder-coated black is the standard and the most forgiving in Texas sun. Bronze, white, and “sandstone” cost a bit more and show dirt differently. We match finish to your trim where it makes sense.
- Picket style and spacing: Standard 3-rail or 2-rail with flat or pressed-point pickets, plus decorative options like rings, circles, or a scalloped top. Tighter picket spacing reads more private and keeps small pets in.
- Gates: Walk gates are standard. Double-drive gates, self-closing hinges, and keypad latches are add-ons – and if your gate approach needs rework, homeowners often pair this with Driveway Repair & Replacement in Rowlett so the swing clears the apron cleanly.
What Aluminum Fence Costs in Rowlett, TX

Plan on $4,000 – $10,000 for a full aluminum fence project in Rowlett, with the lead range for this job at $3,500 – $9,000. The low end is a short 4′ run on flat ground with standard black pickets. The high end is 200+ linear feet of 6′ industrial-grade with a drive gate and decorative top rail.
What pushes a job up or down:
- Linear feet and height: the biggest single driver. Doubling footage roughly doubles material.
- Site conditions: root-covered or rocky runs, tight lot lines, or a steep grade all add labor. Rowlett’s infill lots and mature trees regularly slow post-setting down.
- Grade and finish: industrial wall thickness and premium powder colors add cost.
- Gates and hardware: a double drive gate with automation can easily add four figures.
- Demo and haul-off: removing an existing fence is priced separately, usually a per-foot charge.
Every written estimate from us is line-item: footage, height, finish, gates, hardware, demo, and permits if any apply. The number you see is the number you pay. No change orders mid-job.
See the difference
Before
After
Before
After
Before
AfterWhat Rowlett Homes Specifically Do to This Job
Rowlett’s build-out happened fast in the 1980s through the 2000s, and most of the houses we fence around Waterview and the Peninsula are brick-veneer single-family homes on tight, fully built-out lots. That means we’re almost never setting posts on open greenfield ground – we’re working between mature trees, existing irrigation lines, and property lines that run close to a neighbor’s fence. Locate calls and careful layout matter more here than they would on a new build. The lakeside homes bring a different reality: shoreline-facing property can touch floodplain and Corps of Engineers permitting, so an aluminum fence on the water side may need elevation and setback review before we order a single panel. The soil is the other constant – blackland clay swells and shrinks hard, so we overbuild the footings rather than trusting standard depth. And because spring hail and straight-line winds are staples here, we anchor gates and end posts heavier than the minimum. Homeowners building out the rear or pool side often pair this with Patios, Walkways & Pool Decks in Rowlett, and that’s the kind of thing we plan together, since pool fencing has its own setback and self-latching rules. We cover all of Rowlett, from 75088 to 75030 and 75089, plus nearby Sachse, Garland, Wylie, and Rockwall, through our Fence Installation service.
Serving Rowlett, TX – Our Local Coverage Area
We serve Rowlett and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Aluminum Fence in Rowlett

Most residential aluminum fence jobs in Rowlett take two to four days once we break ground, plus a 48-hour utility locate window before that. Small runs of 100 feet or less often finish in two days; larger jobs with a drive gate run three to four. Call (888) 426-8078 for a firm timeline on your lot.
It depends on height, location, and whether your property touches the lake or floodplain. Front-yard and shoreline fencing typically triggers review; backyard runs within your plat lines often don’t. We pull what’s required and pass inspection, and we’ll flag it in your estimate – call (888) 426-8078 to talk it through.
The range is $4,000 – $10,000 installed, with most jobs in the $3,500 – $9,000 band. Footage, height, grade, gates, and demo are the movers. Call (888) 426-8078 for a free line-item quote – estimates are free.
Yes. We set footer holes only at the posts, not a continuous trench, so lawns recover fast. If a drive gate approach or apron needs work, that’s a separate scope – which is why some Rowlett homeowners pair this with Driveway Repair & Replacement in Rowlett. Call (888) 426-8078 and we’ll scope both.
Every aluminum fence project is covered by the 730-Day Done Right Promise – if a post shifts, a gate sags, or a finish fails prematurely, we make it right, in writing. Aluminum itself needs very little upkeep compared to wood. Call (888) 426-8078 for a free estimate.
Ready for a Quote on Your Rowlett Aluminum Fence?
We’ll come to your property, walk the line with you, and hand you a written estimate with footage, height, finish, gates, and any permit costs spelled out – free, with no pressure. Call (888) 426-8078 and a live person answers any hour. Tell us your address and roughly where you want the fence to run; from there we’ll book an on-site visit and talk through your options.
Written by the team at Groundwork Construction Co.












