







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Aluminum Fence in Garland: What It Costs and How Long It Takes
An aluminum fence in Garland typically runs $4,000 to $10,000, and most residential jobs are finished in two to four days once the panels arrive on site. That range covers a standard 150 to 200 linear feet of 4-foot ornamental aluminum with a walk gate, set in concrete footings. Ornamental aluminum is the fence you meet at subdivision entrances and around pools because it’s welded, rust-resistant, and holds a crisp black or bronze finish. Call (888) 426-8078 for a free on-site estimate.
How an Aluminum Fence Goes In, Day by Day

We do this in a sequence that breaks down into five stages, and knowing what happens on day one versus day three makes the whole job easier to plan around. Here’s the real order.
- Layout and locate. We walk the property line with you, mark corners and gate positions with stakes and string, and call Texas 811 to have buried utilities flagged. This stage takes about half a day, and it’s your window to move a gate post or change a run before anything gets dug.
- Demolition and prep. If a wood or chain-link fence is coming out, we pull it and haul it off, then clear roots and vegetation along the run. On a typical Garland lot, this is one day. You decide here whether the old concrete footings get broken out or left in place.
- Post holes and footings. Posts go in at roughly 6 to 8 feet on center and get set in concrete footings dug to about 24 to 30 inches, below the frost line and past the active clay zone that drives so much movement around here. Footings need about 24 hours to cure before panels hang. This is the stage that decides how straight your fence stays over the next decade.
- Panel and gate installation. Rails, pickets, and gate hardware get set once the concrete cures. A two-person crew hangs roughly 100 to 150 feet of aluminum panels a day, so a 200-foot run with a walk gate fits into one long day or a full two depending on terrain and grade changes.
- Final walkthrough. We check plumb, gate swing, latch alignment, and touch up any field scratches with factory-matched touch-up paint. You sign off the same day, and that’s when the workmanship warranty starts.
We handle the permit pulling where Garland requires it, schedule the inspection, and don’t hand the job off once it’s sold. When the wider project comes up, like a property where the fence ties into a gate column or a new walkway, that’s part of a full Fence Installation in Garland plan we can walk through together.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Aluminum Fence Options You’ll Actually Choose Between
Aluminum isn’t one product. What you pick here drives the price, how it ages, and whether it suits your lot. Here are the choices that matter most.
- Residential vs. industrial grade. A lighter 3-rail residential grade is fine for a backyard boundary. Commercial-grade with thicker posts and heavier pickets costs more and is what you want if you’re fronting a busy road or corralling a large dog.
- Height. 4-foot is the most common backyard height. 5-foot gives more privacy and containment; 6-foot costs more and some HOAs frown on it. Confirm your HOA rules before you commit.
- Finish. Factory powder-coat in black, bronze, or white is the standard and holds up well in sun. Black hides dirt and looks sharp next to brick; bronze reads warmer next to stone and tan stucco. Custom colors cost extra.
- Picket style and spacing. Flat-top pickets with 4-inch spacing are the standard look; 2-inch “pool code” spacing is tighter, uses more material, and costs more per foot. Spear-top or arched tops are decorative upgrades.
- Gates and hardware. A walk gate adds cost; a double-drive gate more. Self-closing hinges and magnetic latches are worth the small upcharge.
When a homeowner is reworking the exterior as a whole, they often pair this with Driveway Repair & Replacement in Garland so the new fence line and the apron meet cleanly instead of leaving a half-finished edge.
What Aluminum Fence Costs in Garland, TX

Plan on $4,000 to $10,000 for a residential aluminum fence in Garland. The low end covers about 100 to 130 feet of standard 4-foot, black powder-coat residential grade with one walk gate. The high end lands around 250 feet of heavier grade, 5-foot height, tight pool-code spacing, and two gates.
What pushes a job to the low or high end:
- Linear feet. The single biggest driver. Every extra 10 feet of run, plus a post and footing, adds real cost.
- Height and grade. Stepping from 4-foot residential to 5-foot commercial-grade can add 30 to 40 percent.
- Picket spacing. Tight pool-code spacing uses more pickets and more welding.
- Gate count and type. A walk gate adds a few hundred dollars; a drive gate adds more.
- Site condition. Sloped, rocky, or root-choked runs need more digging and more footings, and old fence removal adds a line item.
A written estimate spells out linear feet, height, grade, post spacing, gate count, footing depth, removal, and permit cost. It does not automatically cover landscape repair, sod replacement, or utility line relocation if one turns up. Upfront pricing is the promise: the number we write is the number you pay, and the 730-Day Done Right Promise backs the workmanship.
See the difference
Before
After
Before
After
Before
AfterWhat Garland’s Older Core and Newer Subdivisions Change About This Job
Garland is a post-war streetcar suburb that grew into a full city, and the building stock splits sharply by construction era. Around the old downtown core and the 1950s and 60s subdivisions in ZIPs 75040, 75041, and 75042, you find small single-story brick ranches on tight, mature lots with established trees and roots running right through the fence line. Those lots are where we hit the most root-and-rock digging and where the concrete footings have to be worked around tree canopies. Out toward the newer master-planned additions, you get larger lots with cleaner lines and fewer surprises.
Garland runs its own permitting and inspections rather than handing them off to the county, so a fence over the standard height or close to a property line can trigger a permit and a look at setback rules. HOA covenants vary block to block, so know your rules before you lock in a height or finish. Our team covers all of Garland, and you can see the full reach on our Garland service-area page. Our technicians have up to 12 years of experience reading exactly these conditions.
Serving Garland, TX – Our Local Coverage Area
We serve Garland and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked – Aluminum Fence in Garland

Most aluminum fence jobs in Garland take two to four days from first dig to final walkthrough. About one to two days go to layout, prep, and footings while the concrete cures, then one to two days to hang panels and gates. A small job under 100 feet can wrap in two days. Call (888) 426-8078 for a realistic timeline for your lot.
Garland requires a permit for fences in some cases, including taller fences and those near a property line, and we pull the permit for you when one is needed. We handle the paperwork and schedule the inspection so it doesn’t stall on you. Call (888) 426-8078 and we’ll tell you whether your project needs one.
Post footings go in along a line we lay out with you at the start, so buried irrigation lines and most plumbing stay clear of the holes. Texas 811 flags utilities before we dig. Established trees near the line get worked around rather than through. Call (888) 426-8078 to walk your lot with us first.
A residential aluminum fence in Garland runs $4,000 to $10,000, with linear feet, height, grade, and gate count driving the difference. The quote is written line by line so you see where every dollar goes. Call (888) 426-8078 for an exact quote; estimates are free.
Every aluminum fence we install is covered by our 730-Day Done Right Promise, one of the longest workmanship guarantees in residential construction. If it’s not done right, we make it right. Call (888) 426-8078 to schedule your free estimate.
Get Your Free Aluminum Fence Estimate in Garland
A free on-site estimate starts the process right. We measure the run, talk through grade, height, finish, and gate layout, and leave you a written line-item number you can compare. When you call (888) 426-8078, a live person answers and schedules a time that works for you. For homeowners reworking the whole yard, we also handle our Patios, Walkways & Pool Decks in Garland and Fence Installation work.
Written by the team at Groundwork Construction Co.












