







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Iron Fence in Balch Springs, TX: What It Takes and What It Costs
An iron fence in Balch Springs usually runs $3,500 to $9,000 for a typical residential run, and most jobs are installed in two to four working days once the layout is set and the materials are on site. The number that matters most is linear feet plus the number of posts, gates and corners. Call (888) 426-8078 and we’ll walk your property line with you and put a written, line-item estimate in your hands – free, no pressure, no surprises when the crew shows up.
How an iron fence gets built here, stage by stage

Iron fence work is less about the panels and more about what happens underground. On blackland prairie soil, the set of the posts decides whether your fence is still plumb in five years. Here’s the actual sequence we follow in Balch Springs.
1. Layout and utility locate (day one, half a day)
We walk the line with you first, then mark corners, gate posts and terminal posts with paint or flags. Before any digging, we call for utility locates – no exceptions, especially on older properties where the water and gas runs may not be where you’d expect. You approve the final layout on the ground before we touch a shovel. This is also where you lock in gate swing direction and hinge side.
2. Demo and prep (day one to two)
If there’s an existing fence, we pull it, haul it off and clear the line. Old posts set in concrete take the most time. We also grade out the strip where the fence sits so the bottom rail sits at a consistent height – on sloped lots, that means stepping panels rather than letting the fence rack downhill.
3. Post setting (day two, then cure time)
Posts go in holes sized to the fence height and soil, set in concrete with proper depth below grade. On the expansive clay common in Balch Springs, we bell the bottom of the hole and keep the concrete collar generous so the post resists the seasonal swell-shrink cycle. Concrete needs to cure before you load the panels, so this is the one stage you can’t rush.
4. Panels, rails, gates and finish (day three to four)
Rails, pickets and gate frames go up, hinges and latches get fitted, and we touch up any field cuts with matching finish. A standard walk gate and a vehicle gate each add hardware time. You walk the line with us at the end and we adjust anything that doesn’t swing or latch clean.
5. Final inspection and walkthrough (same day as finish)
We check post plumb, gate clearance, latch alignment and rail height, clean up the site, and hand you the maintenance sheet. The installation is backed by our 730-Day Done Right Promise – if something we installed isn’t right, we make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The options you’ll actually choose between on an iron fence
There’s no such thing as “just an iron fence.” What you pick at the front end shapes the price and how the fence ages. These are the real forks in the road:
- Wrought iron vs. welded steel (tubular). True wrought iron is heavier, denser and ages beautifully, but it costs more per foot and needs periodic painting. Welded steel panels are lighter, quicker to set and usually the default for residential runs – less expensive, still strong, but you’re trading a bit of weight for value.
- Finish system. Powder coat is the workhorse: durable, low-maintenance and available in several colors. A primed-then-painted finish costs less up front but needs recoating every few years, which matters with our heat and humidity.
- Picket spacing and height. Tighter spacing (for small pets or a pool barrier) adds linear pickets and drives cost up. Standard residential height runs about 4 to 6 feet; a taller fence adds material and post depth.
- Gate type and hardware. A walk gate, double drive gate or automated gate all change the hardware and post requirements. Automated gates need a power drop at the gate post and heavier hinges.
- Post anchors and mount style. In-ground concrete-set posts are standard. Surface-mount plates over an existing concrete wall or curb are an option in some layouts and change the prep work.
Some homeowners pair the fence line with a new hardscape in the same project; if that’s on your list, our Patios, Walkways & Pool Decks in Balch Springs work runs on the same schedule visits.
What iron fence costs in Balch Springs, TX

Most residential iron fence projects here land between $3,500 and $9,000. Here’s how the pieces move that number:
- Linear feet. The single biggest driver. A small front-yard run sits near the low end; a full perimeter with multiple gates lands at the high end.
- Material choice. Welded steel is the value play; heavier wrought iron panels push you toward the upper range.
- Corner posts, terminal posts and gates. Every corner, end and gate post carries extra hardware and bracing. A drive gate costs more than a walk gate.
- Demo of an existing fence. Tearing out concrete-set posts and hauling it off adds labor.
- Site condition and access. A tight side yard, sloped ground, or a long pull from the street adds time.
A written estimate itemizes linear feet, post count, gate count, finish, demo and disposal so you can see exactly where your dollars go. What’s typically not included without a line item: automated gate operators, electrical drops at a gate post, and any landscaping restoration. If your project is part of a full Fence Installation in Balch Springs plan, we price it together so nothing double-bills. Want the broader picture on how we handle fences? See our Fence Installation service. No-hassle upfront pricing – the number you see is the number you pay.
See the difference
Before
After
Before
After
Before
AfterWhat Balch Springs homes specifically do to this job
Balch Springs sits in the heart of the Texas blackland prairie, and that expansive clay decides a lot about an iron fence. When the ground swells after a wet spring and shrinks in a dry summer, anything set shallow works loose. We set posts deeper and with a wider concrete collar here than we would on stable ground, and we plan stepped panels on sloped lots rather than letting a fence rack. Much of the local housing stock is mid-century to 1970s single-story ranch homes on pier-and-beam or shallow slab foundations, and a lot of those properties still have original utility runs in unpredictable spots – which is why the locate call comes before any digging. Older neighborhoods around 75180 also deal with heavy rain pushing soil movement, and iron fence posts are not immune. That’s the same movement that shifts pier-and-beam homes and makes doors stick. The good news is that a properly set iron fence holds up better in this clay than wood; there’s no rot cycle, so you’re not replacing panels every decade or two. We cover the neighborhoods along the 75180 ZIP and across Balch Springs with the same staged approach. If you’re adding a structure in back, many homeowners pair a fence project with ADU Design & Permitting in Balch Springs so the layouts are coordinated.
Serving Balch Springs, TX – Our Local Coverage Area
We serve Balch Springs and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked – iron fence in Balch Springs

Most residential iron fence installations take two to four working days, with the biggest variable being concrete cure time for the posts. A simple front-yard run can be done in about two days; a full perimeter with gates and demo of an old fence runs closer to four. Call (888) 426-8078 and we’ll give you a realistic schedule for your property.
Permit requirements depend on fence height, location, and whether it sits in an easement or at a corner with sight-distance rules – many residential fences fall under city rules without a separate permit. We confirm the current Balch Springs rules for your lot before we build, and we’ll tell you plainly whether a permit applies. Call (888) 426-8078 for a free on-site read on your project.
Yes, in the vast majority of cases. That’s exactly what the utility locate step is for – we find the buried lines first and adjust post positions around them rather than digging through them. On older Balch Springs properties with uncertain original utilities, the locate call is what protects you. Call (888) 426-8078 to talk through your layout.
A typical residential iron fence here runs $3,500 to $9,000, with linear feet, material grade, gate count and existing-fence demo driving the difference. A written, itemized estimate tells you exactly which of those is moving your number. Call (888) 426-8078 for a free quote.
Every iron fence we install is covered by the 730-Day Done Right Promise – one of the longest workmanship guarantees in the residential construction space. If something we installed fails, we make it right. Call (888) 426-8078 to schedule your free estimate.
Get a free iron fence estimate in Balch Springs
We’ll come out, walk your property line, and give you a written, itemized estimate for your iron fence in Balch Springs – free, with no-highassle pricing and 0% financing for 18 months available. Call (888) 426-8078 to schedule your free project estimate; calls are answered by a live person, 24/7. We answer your questions, confirm what’s included, and lay out a realistic schedule before any work begins.
Written by the team at Groundwork Construction Co.












