







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Metal Roofing in Wylie, TX: What It Costs and How Long It Takes
Metal roofing in Wylie, TX runs $15,000 – $40,000 for a typical single-family home, and most installations take five to nine working days once the material is on site. Standing seam costs more than exposed-fastener panels because of the concealed clips and the longer panel runs a two-story Wylie house usually needs. If you own a brick two-story off FM 544 or a newer build in one of the subdivisions off Highway 78, call (888) 426-8078 for a free on-site estimate and a written line-item quote before you commit to anything.
The Five Stages of a Metal Roof, From Tear-Off to Final Inspection

Every metal job we run follows the same sequence, and each stage has a decision only the homeowner can make. Here’s what actually happens.
Stage 1: Roof inspection and material order (1 – 2 days)
We start on the roof, not in a brochure. That means checking the decking for soft spots, measuring the actual square footage with all the valleys and hips broken out, and confirming the slope. If your pitch is under 3:12, a standing seam install usually needs a membrane underlayment system instead of exposed panel with battens. At this point you choose the panel profile and the finish color, because lead time on a custom color runs longer than on a stock finish. Ordering happens once you sign the written quote.
Stage 2: Tear-off and decking prep (1 – 2 days)
We strip the old shingles to the deck, haul the debris, and then inspect the decking board by board. On Wylie’s newer builds, the original deck is usually in good shape. On the older ranch homes near downtown, we regularly find a layer or two of old shingles and a few soft boards that get replaced. New underlayment goes down before anything else. This stage can’t be compressed: if the deck isn’t sound, no panel clip will save the roof.
Stage 3: Panel layout and install (2 – 5 days)
Standing seam panels are cut to the exact run length, so there are no horizontal laps across the roof. Crews lay the panels out so the seams land on the correct ribs, fasten the concealed clips, and roll the seams. On a complex hip-and-valley roof, this stage runs longer than on a simple gable. Exposed-fastener panels go down faster because there’s no seaming, but every screw is a potential leak point over twenty years, which is why we don’t push them toward hail-belt homeowners.
Stage 4: Flashing, valleys, and penetrations (1 day)
This is where roofs leak. Chimneys, vent stacks, skylights, and the transition where a metal roof meets a lower porch or garage all get their own custom flashing. We fabricate these, not buy a universal piece. On a Wylie house where the garage, main roof, and porch are all at different pitches, this is often a full day on its own.
Stage 5: Final inspection and punch list (same day)
We walk the roof with you once the panels are down, check every seam and fastener, and confirm the chimney caps and vents are sealed. If your metal roof replaces a shingle roof, the permit inspection happens at this stage, tied to the final sign-off. You get the punch list in writing before we leave.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
Standing Seam vs. Exposed-Fastener vs. Stone-Coated: The Real Trade-Offs
The panel type is the single biggest decision on this job. Each one hits a different balance of cost, longevity, and hail performance, and Wylie’s weather makes all three matter.
- Standing seam panels: the concealed fastener system with raised seams and no exposed screws. The most weather-tight option, gets the longest service life, and holds up best through hail. Costs more upfront, and needs an experienced seamer on site, so it’s not the cheapest route.
- Exposed-fastener panels (screw-down): the budget choice for a metal roof. Faster to install and cheaper per square. The trade-off is the screw gaskets, which age over twenty years and can back out or leak, so they don’t hold up as well on a hail-belt roof.
- Stone-coated steel: stamped steel tile or shake shapes with a granule coating. Looks like tile or a traditional shingle but weighs much less. Middle of the price range, a good fit for homeowners with an HOA that has cosmetic roof restrictions.
- Panel gauge and paint finish: thicker steel (24-gauge versus 26-gauge) matters for hail and wind. A premium paint system like Kynar 500-type finishes holds color across the North Texas UV load better than a basic poly finish. That’s a real line item, not a marketing upcharge.
- Color and panel length: a custom color and a long panel run cost more than a stock color and a shorter panel. Stock finishes ship faster and stay cheaper. Longer panels reduce horizontal laps but require a wider delivery footprint on a tight lot.
What Metal Roofing Costs in Wylie, TX

Typical metal roofing in Wylie lands between $15,000 and $40,000. A simple gable roof on a single-story ranch comes in at the low end; a two-story brick home with a complex hip-and-valley roof, a custom color, and a full deck replacement pushes toward the top.
Four variables move that number:
- Roof size and complexity: squares of roofing, plus the number of hips, valleys, dormers, and penetrations. A complex Wylie roofline needs more panels, more flashings, and more labor hours than a simple one.
- Deck condition at tear-off: replacing soft boards adds cost. It’s the one line item we can’t quote until the old roof is off, so we flag it in writing before we start, not after.
- Panel system: exposed-fastener is the baseline. Standing seam and stone-coated steel both sit higher. A 24-gauge standing seam roof on a two-story home sits near the top of the range.
- Permit and inspection scope: a full reroof permit in Wylie is part of the job. Any structural repair found under the deck expands the permit scope.
Your written estimate lists the panel system, gauge, color, underlayment, deck replacement allowance, flashing, and the permit. It excludes things like deck repair beyond the allowance and structural work under the sheathing, unless we’ve found it during the inspection. No surprise change orders mid-job: the number on the quote is the number you pay.
See the difference
Before
After
Before
After
Before
AfterWhat Wylie’s Climate and New-Build Housing Stock Do to a Metal Roof
Wylie sits in the hail-and-tornado belt, and that changes how a roof is specified. Hail resistance is not a nice-to-have on a roof here: it drives panel gauge, seam style, and paint finish, because a lighter fastener-down panel on a hail-year roof shows every dent. The hotter part of the story is the blackland prairie clay under much of Wylie’s former farmland. It swells in wet springs and shrinks through dry summers, and that movement shows up at the roof edge as fascia and soffit gaps. On tight modern lots, where the eave overhang is only a foot or two, we check the roof-to-wall transition and the attic ventilation carefully when a roof is replaced.
Most of the homes we work on in Wylie are 2000s-to-present builds, post-tension slab-on-grade brick homes with original architectural shingles reaching end-of-life. The older ranch homes near downtown off FM 544 and Highway 78 often still have a first or second layer of shingles and, occasionally, a soft deck to go with it. If your replacement is part of a full Roofing in Wylie scope that also covers gutters and fascia, we plan the sequence so nothing gets torn apart twice. Homeowners here often pair a new metal roof with Window Replacement in Wylie and Impact Windows & Doors in Wylie, since the same hail storms hit both, and the combined project spreads the disruption across one permit window.
HOA rules are a real factor. Some Wylie subdivisions restrict visible roof material, so confirm the panel profile and color with your HOA before you sign. We can help with the submittal paperwork, but the approval is on your timeline, not ours. To see the neighborhoods we cover around Wylie, Wylie is the place to start.
Metal roofing is one of seven core services we run, alongside kitchen and bath remodels, windows and doors, fencing, pavers, and additions. Browse the full Roofing scope if you’re comparing this against a repair instead of a full replacement.
Serving Wylie, TX – Our Local Coverage Area
We serve Wylie and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Metal Roofing in Wylie

Most metal roofing in Wylie runs five to nine working days on site, from tear-off to final inspection. A simple single-story roof can finish in five; a two-story home with a complex hip-and-valley roof, a full deck replacement, or a custom color runs toward the top of that range. Add a few weeks before the install date for panel manufacturing and delivery on a custom color. Call (888) 426-8078 for a timeline based on your actual roof.
Yes, a full reroof permit is part of the job, and the work gets inspected. We pull the permit for you and schedule the inspection tied to the final walkthrough, so you don’t handle the paperwork. If the tear-off surfaces a structural issue, the permit scope expands and we quote the change in writing before doing the work. Call (888) 426-8078 and we’ll walk you through the permit timeline for your address.
In most cases, yes. On a sound post-tension slab home in a Wylie subdivision, the structure stays, the decking is inspected, and only soft boards are replaced. What we never skip is the deck inspection: a metal panel bolted to a soft deck will fail at the fasteners. If the inspection finds structural damage, we quote the fix before installing anything. Call (888) 426-8078 to schedule a roof inspection.
Metal roofing in Wylie runs $15,000 – $40,000, versus a shingle roof at $8,000 – $20,000. The gap is the panel material and the labor for the concealed-clip system. A standing seam roof at the higher gauge holds up to hail and holds its color far longer than asphalt shingles, so the service life is the honest comparison. Call (888) 426-8078 for a line-item quote against your current roof.
Every metal roof we install is backed by the 730-Day Done Right Promise: if the workmanship isn’t right, we make it right, for two full years after the install. The panel manufacturer’s own finish and hail warranty rides on top of that and depends on the panel system and gauge you choose. We put both warranties in writing on the quote. Call (888) 426-8078 for a free estimate that spells out what’s covered.
Get a Free Metal Roofing Estimate in Wylie
If you’re weighing metal roofing in Wylie against another shingle roof, the free on-site estimate is where the numbers turn real. We measure the roof, inspect the deck, and hand you a written line-item quote with the panel system, gauge, and permit broken out. A live person answers at (888) 426-8078 any hour, and the estimate comes with no obligation. Proposals over $10,000 qualify for $1,000 off and 0% financing for 18 months.
Written by the team at Groundwork Construction Co.












