







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Aluminum Fence in Balch Springs: What It Costs and How Long It Takes
An aluminum fence in Balch Springs typically runs $4,000 to $10,000 for a standard residential run, with most full-property jobs landing between $3,500 and $9,000 once layout and gate count settle. A straightforward run is usually one to three days of install after a 7 to 21 day material lead time. Aluminum is the right call here when you want a clean, rust-proof line that holds up to blackland prairie weather and won’t need repainting every few summers. Call (888) 426-8078 for a free on-site estimate.
How an Aluminum Fence Goes In, Stage by Stage

Aluminum fencing fails on the small decisions, not the big ones, so we walk every stage with you before a single post goes in the ground.
Stage 1: Walk the line and set the layout (day 1, 60 to 90 minutes). We mark the property boundary, confirm where gates land, and check for buried irrigation, gas, and the old fence footings. You decide the run height, gate swing direction, and where the walk-through gap belongs. This is the stage that saves the project, because aluminum panels are pre-cut and a wrong post spacing means a return trip.
Stage 2: Demo and prep (day 1 or 2, 4 to 8 hours). Old wood, chain link, or failing posts come out, and we set the new layout against the grade. Balch Springs lots often slope toward the street after decades of soil movement, so panels need to rack with the grade rather than step in hard increments. You approve the transition points.
Stage 3: Set posts in concrete (day 2, 3 to 5 hours). Aluminum posts get set in a concrete footing sized for the height and wind load, then cured before the panels go on. This is the part that determines whether the fence stays plumb through shrink-swell cycles. You don’t have to decide anything here; we just keep you posted on cure time.
Stage 4: Hang panels, gates, and hardware (day 3, 4 to 6 hours). Panels, pickets, and gate frames go on, and self-closing hinges and latches get aligned. You pick the finish, the picket style, and the gate hardware grade before this stage.
Stage 5: Punch list and walkthrough (day 3, 30 minutes). We check plumb, latch alignment, and cap rails, then hand you the warranty paperwork. The whole job is covered by the 730-Day Done Right Promise, so if a post shifts or a latch drifts, we come back and make it right.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Aluminum Fence Choices You’ll Actually Make
- Residential vs. commercial grade. Residential runs are lighter gauge and cost less; commercial panels are heavier and better for long runs and windy exposure. For a typical Balch Springs backyard, residential grade is plenty.
- Height (4 ft vs. 5 ft vs. 6 ft). Taller means more material and more footing, which pushes the price up. Pool and code considerations matter, so we confirm height against your specific property line before quoting.
- Picket style (flat-top, spear-top, pressed-point). Cosmetic, but it changes the per-foot price slightly. Spear-top is the most common choice here.
- Finish and color (black, bronze, white, custom powder coat). Standard black and bronze cost less; custom powder coat adds lead time and cost.
- Rackable vs. stepped panels. Rackable panels follow a slope; stepped panels handle bigger drops. Your lot determines which you need.
- Gate grade and hardware. A standard pedestrian gate is one thing; a wide driveway gate with heavier hinges and a latch rated for daily use is another. This is often the biggest line item after linear footage.
Most homeowners in Balch Springs land on black or bronze residential grade, 4 to 5 feet, with one pedestrian gate. We’ll show you the trade-off for each upgrade so you’re choosing on purpose, not by default.
What an Aluminum Fence Costs in Balch Springs, TX

Aluminum fence installation in Balch Springs runs $4,000 to $10,000, and most of our jobs here land in the $3,500 to $9,000 band. Here’s what actually moves that number:
- Linear footage. The single biggest driver. A small backyard run sits at the bottom; a full-perimeter run with a front yard is at the top.
- Gate count and grade. Each gate adds cost, and a wide driveway gate with heavy hardware is a meaningful jump.
- Old fence removal. Tear-out and haul-away of an existing wood or chain link fence adds labor and disposal.
- Grade and footing difficulty. Sloped lots and hard caliche require more concrete and longer posts, which raises the number.
- Finish and custom color. Standard black and bronze are lowest; custom powder coat adds material cost and lead time.
A written estimate itemizes linear footage, post count, footing depth, gates, hardware, tear-out, and finish. It doesn’t include landscaping repair after trenching, sod replacement, or an HOA resubmittal fee. Upfront pricing means the number you see is the number you pay. Ask for the itemized quote; it’s free and there’s no pressure on it.
See the difference
Before
After
Before
After
Before
AfterWhat Balch Springs Lots and Soil Do to an Aluminum Fence
Balch Springs sits squarely on the Texas blackland prairie, where expansive clay soils swell in wet seasons and shrink in dry ones. That movement is the reason post footings here need to be set deeper and cured longer than on stable ground, and it’s the reason we don’t cut corners on concrete. In older neighborhoods around ZIP 75180, we regularly see pier-and-beam ranch homes from the mid-20th century into the 1970s, often on original plumbing and electrical. That matters for fencing because we’re running a line around mature lots with buried irrigation, old utility lines, and fence lines that have crept over decades of settling. When we demo an old wood fence here, we often find the original posts barely set, which explains why so many of them lean after a wet spring. We build to the house, not the old fence line, so you get a straight, plumb result that holds. If you’re working up to a fuller project, this is often part of a Fence Installation in Balch Springs plan, and we’ll coordinate the aluminum run with it. Homeowners often pair the fence with Driveway Repair & Replacement in Balch Springs so the whole approach looks intentional, and sometimes with Patios, Walkways & Pool Decks in Balch Springs when the fence line defines a backyard living area. We serve all of Balch Springs and the surrounding area.
Serving Balch Springs, TX – Our Local Coverage Area
We serve Balch Springs and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Aluminum Fence in Balch Springs

Plan on one to three days of install once materials arrive, plus a 7 to 21 day lead time for panels and gates. Standard black and bronze ship faster than custom powder coat, and a small run with no tear-out can finish in a single day. Call (888) 426-8078 and we’ll give you a real timeline against your actual layout.
Most residential aluminum fences here don’t require a building permit, but height limits, lot-line rules, and HOA covenants can apply, so we check before we order. Pool enclosures and front-yard runs are the cases where a permit and inspection most often come into play. On the estimate we’ll confirm what applies to your address. Questions? Call (888) 426-8078.
No, in a normal install we don’t touch plumbing or the house structure. We locate buried irrigation and utilities before setting posts, and we route the line clear of plumbing that runs beneath older pier-and-beam homes. If something is buried where a post needs to go, we adjust the layout rather than risk a line. Call (888) 426-8078 to walk your lot with us.
A standard residential aluminum fence here runs $4,000 to $10,000, and most jobs land closer to $3,500 to $9,000 depending on footage and gates. Tear-out, slope, and finish push the number toward the high end. Call (888) 426-8078 for a free itemized estimate on your specific line.
The 730-Day Done Right Promise covers the workmanship, and the manufacturer covers the aluminum and powder coat. If a post misaligns or a gate latch fails within that window, we come back and make it right at no cost. We’ll spell out what’s covered before you sign. Call (888) 426-8078 with questions.
Get a Free Estimate for Your Aluminum Fence
We’ll walk your property, measure the line, and hand you an itemized quote with linear footage, gate count, footing depth, and finish spelled out. No pressure on the estimate, and we answer live, 24/7. If it’s part of a broader project, we can fold in our Fence Installation service and any related work in one scope. Call (888) 426-8078 to schedule your free estimate for an aluminum fence in Balch Springs and get the number you’ll actually pay.
Written by the team at Groundwork Construction Co.












