







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Chain Link Fence in Garland, TX: What It Costs and What It Takes
A chain link fence in Garland typically runs $3,500 to $9,000 for a standard residential lot, installed in one to three days. The number lands on the high end when you’re fencing acreage out toward the eastern ZIPs, pulling old posts, or running gates wide enough for a truck. Call us at (888) 426-8078 for a free on-site estimate. Our technicians have up to 12 years of experience and every job is backed by our 730-Day Done Right Promise.
How we build a chain link fence in Garland, start to finish

We don’t guess and we don’t come back twice. One crew, one trip, a fence that’s done when we leave. Here’s the actual sequence.
Day one, stage one: walk the line and set the corners
We start by pulling the layout string around the property line and verifying it against the plat. For bigger lots in Garland, that means checking where the fence meets the detached workshop, shed, or shop building so it doesn’t block a door swing or a service drive. You decide the final gate locations here, and this is also when we have you confirm setback from any easement or drainage swale. That conversation takes about 30 minutes and saves a week of rework.
Stage two: dig and set posts
Most of the day is spent setting posts. Line posts go about 24 inches deep in Blackland clay, corners and gates go deeper and get concrete. Garland’s soil is the real variable here: in a wet-spring lot the clay is nearly workable, and in a dry-summer lot it can stop a hand auger cold. We bring power augers. On a typical 150-foot residential run this stage takes four to six hours.
Stage three: rails, tension wire, and mesh
Rails go into post loops, the tension wire gets stretched along the bottom, and the mesh rolls out and gets tensioned at each end post. We pull it taut, tie it off every couple of feet, and stretch it before we tie. A slack fence is a fence that sags by year two. This is a two-to-three-hour stage on a normal job.
Stage four: gates and hardware
Gate posts are the ones people underestimate. If you want a double drive gate wide enough to pull a trailer through, the posts have to be bigger and set in more concrete, and that happens in stage two, not here. We install the gate frames, hinges, latches, and any operator now. You decide whether you want a walk gate with a self-closer or a plain gravity latch.
Stage five: final tension, cleanup, and walkthrough
We re-tension the whole run, tighten every fitting, and walk you through the fence line by line, gate by gate. We haul off the old mesh and posts if there were any. Most residential Garland jobs are finished in a single day; acreage runs stretch to two or three.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The chain link specs you’ll actually choose between
Chain link isn’t one product. It’s a set of choices, and each one has a trade-off you should know before you sign anything.
- Gauge of mesh: 11.5-gauge is the light residential standard and the cheapest way to enclose a yard. 9-gauge is noticeably stiffer and holds its shape against a dog that leans on it. 6-gauge is commercial weight and rarely needed at a Garland single-family lot.
- Height: 4-foot fences keep kids and small dogs in. 5-foot is the sweet spot for most Garland backyards. 6-foot and up is what most insurance carriers and fence codes want around a pool or shop building.
- Framework: 1 3/8″ line posts are fine for a short residential run. 1 5/8″ or 2 3/8″ posts are what you want when the run is longer than about 150 feet or the wind loads matter.
- Coating: Galvanized is the baseline and handles North Texas weather well. Vinyl-coated is often what Garland HOAs want for the color match, and it adds a modest premium. Black or green vinyl-coated mesh also lasts longer against the clay dust.
- Gates: Standard walk gates run four feet. A double drive gate is where the price jumps, and where the post footing and hardware need to be engineered, not selected from a bin.
- Tension wire and top rail: A top rail plus a bottom tension wire keeps the mesh from bowing. It’s a small add-on that separates a fence that lasts 15 years from one that lasts 8.
What a chain link fence costs in Garland, TX

For a typical residential lot in Garland, chain link fence installation runs $3,500 to $9,000. That’s the honest range for the work. Here’s what pushes a job toward the top of it:
- Linear footage: The single biggest driver. A 100-foot run and a 300-foot run are different jobs with different post counts and mesh quantities.
- Gate count and width: A drive gate with heavy posts and hardware can add a meaningful chunk on its own, especially if you want an opener or a self-closer.
- Removal of an existing fence: Pulling old posts, breaking up their footings, and hauling off the mesh adds labor. Old posts set in concrete in Garland’s clay can be stubborn.
- Terrain and slope: A flat lot everywhere is the easy case. A run that drops or rises along the property line needs racking and extra posts.
- Permit scope and HOA: A fence permit and inspection pulls time and a fee; some Garland HOAs also require a submittal and specific color or height.
What a written estimate from us includes: mesh, posts, rails, tension wire, concrete footings, gate hardware, labor, cleanup, and haul-away. What it can’t include until we’re on site: how much rock we hit while digging, and whether the old post footings come out clean. We don’t hide those, and upfront pricing means the number you see on the written quote is the number you pay, not a lowball that balloons after day one. Financing is available at 0% for 18 months, and projects over $10,000 get $1,000 off.
See the difference
Before
After
Before
After
Before
AfterWhat Garland homes do to this job
Garland’s lot sizes and age split shape chain link work here more than in most cities we serve. Around the older core in the 75040 and 75041 ZIPs, the 1950s and 1960s single-story brick ranches have property lines that sit close to detached garages and shop buildings, so the fence layout often has to skirt a structure, not just enclose a rectangle. Out toward the newer 1970s-90s subdivisions and the master-planned additions, the lots are wider and the run is longer, which is where you actually feel the footage cost. The Blackland clay runs through both areas. Posts set in a wet spring hold well; posts set in a dry summer need more concrete and sometimes a deeper footing to stay put. On a job near the downtown core, one more thing matters: some of those older homes have fence lines that were never surveyed and don’t match the plat. We verify before we dig, and we’re honest about it if the line needs a boundary survey first. Garland runs its own permitting and inspections, so a fence permit here follows the city’s process, not the county’s. That’s a small thing, but it’s the kind of thing that gets missed by a crew used to working elsewhere. If your fence is part of a full Fence Installation in Garland project, we scope the whole thing together.
Serving Garland, TX – Our Local Coverage Area
We serve Garland and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently asked, chain link fence in Garland

Most residential chain link fence jobs in Garland are completed in one to three days. A typical lot under 150 feet with one or two gates is a one-day job; acreage runs with drive gates and old fence removal stretch to two or three. Call (888) 426-8078 and we’ll give you a realistic timeline for your lot.
Often yes. Garland runs its own permitting and inspections, so we check the requirements for your address before we start and handle the permit for you. Height and setback rules and HOA requirements can affect the final scope, so it’s worth confirming up front. Call (888) 426-8078 with your address and we’ll sort out what applies.
A chain link fence in Garland costs $3,500 to $9,000 for a standard residential lot. The number moves with linear footage, gate count and width, whether an old fence needs removing, terrain, and HOA requirements. Call (888) 426-8078 for a free written estimate with line-item pricing.
No, not on the work we quoted. Upfront pricing means the number on the written estimate is the number you pay. If we hit something we couldn’t see, like a buried concrete footing or a rock shelf, we stop, show you, and get your approval before anything changes. Call (888) 426-8078 to schedule your estimate and get the quote in writing.
Every chain link fence we install is covered by our 730-Day Done Right Promise. If something we built isn’t right, we come back and make it right, in writing. Ask for the warranty terms with your estimate. Call (888) 426-8078 for details.
Get a free chain link fence estimate in Garland
Fencing is often paired with other work, and it’s worth doing in the same trip. Whether you’re adding a Concrete Driveways & Concrete Work in Garland project out to the shop or a Asphalt Driveways & Resurfacing in Garland refresh, we can scope the whole yard in one visit. We connect homeowners across Garland with independent local professionals who do the work, and our Fence Installation service covers the full run when a chain link fence is part of a wider plan. Call (888) 426-8078 for a free on-site estimate and a written, line-item quote.
Written by the team at Groundwork Construction Co. of Mesquite.












