







Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Gutters & Accessories in Garland, TX: What They Cost and How Long They Take
Seamless aluminum gutters on a typical Garland ranch run $1,400 to $3,800 installed, including downspouts, hangers, and leaf guards on the runs under your trees, and most homes are finished in a single day. If you’re also correcting grading or tying into a drainage line along the slab edge, add $600 to $2,200. Call (888) 426-8078 for a free on-site measurement and a written line-item quote.
What a Garland Gutter Job Looks Like, Stage by Stage

We don’t guess at footage from a satellite image. The sequence below is how a Gutters & Accessories job actually moves once a homeowner in Garland picks up the phone.
Stage 1: On-site measure and roofline check (60 – 90 minutes)
We walk the perimeter, measure every run, count corners, and note the roof pitch. On Garland’s older single-story brick homes, we pay close attention to fascia condition, because a 1950s or 1960s fascia board that’s been slowly rotting behind an old gutter can’t safely carry a new hanger. If we find soft wood, you’ll see it in the estimate before we leave. This is also when you decide on material and profile.
Stage 2: Material choice and written quote (same visit, 1 – 2 days to finalize)
You’ll choose aluminum versus steel, 5-inch versus 6-inch, and the color. We hand you a line-item quote: footage by run, number of downspouts, hanger spacing, guard type, and haul-off. No change orders later, no “we found extra footage.” If gutters are part of a larger scope, this is where we coordinate with our Roofing in Garland work so the drip edge and gutter line are handled in the right order.
Stage 3: Removal and prep (half a day)
Old gutters come down, nails and spikes get pulled, and we clear the debris. On a slab-on-clay home, the old downspout splash blocks graded water straight back under the foundation, so we look at where the water’s been going for the last forty years before we decide new discharge points. You don’t have to do anything at this stage except keep vehicles off the driveway.
Stage 4: Fabrication and install (same day to a day and a half)
Seamless aluminum is formed on site to each run’s exact length, which means no joints for water to find. We set hangers every 24 inches (closer in high-wind zones), install downspouts, and fasten guards. On Garland’s two-story brick-and-frame homes in the northern ZIPs, the second-story runs take longer and often need scaffolding or a lift.
Stage 5: Water test and walkthrough (30 minutes)
We run a hose down each run, confirm the pitch carries water to the outlet without ponding, and check that discharge lands at least four feet from the foundation. You walk it with us, and the work is covered under our 730-Day Done Right Promise. Most jobs stay on this timeline; the exception is a home that needs fascia repair under the old gutter.
Styles & brands we work with
- Kitchen remodeling
- Bathroom remodeling
- Home additions & ADU
- Roofing
- Windows & doors
- Driveway & pavers
- Fence
The Gutter Options You’ll Choose Between
There’s no single “best” gutter for a Garland home. It depends on your roofline, your trees, and how long you plan to stay.
- Seamless aluminum, 5-inch: The standard for most Garland homes. Rust-proof, light, and the best value at around $6 to $11 per linear foot installed. It dents under heavy impact, so keep it off the north-facing run under a pecan tree if hail is a routine concern.
- Seamless aluminum, 6-inch: Panels run about 20 – 30% more than 5-inch. Worth it on long, steep roof runs and bigger roofs where 5-inch simply can’t move the volume during a North Texas downpour.
- Galvanized or steel: Heavier, holds up better to hail and falling limbs, but costs more and needs paint maintenance over time. Suits a homeowner who’s replacing gutters once and wants them to outlast the roof.
- Leaf guards (mesh vs. reverse-curve): Mesh is the common choice under Garland’s mature trees; reverse-curve systems work well where leaves are the main problem but struggle with the smaller seed pods from pecans.
- Downspout and discharge options: Standard downspouts, subsurface drainage tied to a pop-up emitter, or rain barrels. Subsurface routing matters here because our clay soil doesn’t soak water away fast, and good grading is half the battle against foundation movement.
- Accessories: Fascia aprons, valley hangers, and splash blocks are the small items that make or break a job. We spec them by name in the quote.
What Gutters & Accessories Costs in Garland, TX

Most Garland gutter replacements land between $1,400 and $3,800, with guards and drainage bringing the typical project to the $1,800 to $4,500 range. Here’s what moves a quote to the low or high end.
| Line item | Typical Garland range |
|---|---|
| Seamless aluminum gutters (installed, per linear foot) | $6 – $11 |
| Downspouts (per downspout, installed) | $90 – $180 |
| Leaf guards (per linear foot, installed) | $4 – $12 |
| Fascia repair (per linear foot) | $15 – $40 |
| Subsurface drainage tie-in | $400 – $1,800 |
Four variables push the number:
- House size and roofline complexity: A 1,200-square-foot ranch with two gables is a different job than a two-story with multiple valleys. More corners and valleys mean more footage and more fabrication time.
- Fascia and soffit condition: On the 1950s and 1960s ranches near downtown Garland, rotted fascia is common and adds both material and a repair day.
- Number of stories: Second-story runs need ladders, lifts, or scaffolding, adding labor and set-up time.
- Guards and drainage: Leaf guards and subsurface discharge are the two add-ons we’re asked about most, and they’re the ones that make the gutters perform long-term on clay soil.
Every estimate we write is line-item and fixed, with the brand and profile named so you can compare apples to apples. Our gutter work is installed by background-checked technicians who arrive in uniform, and pricing matches the quote you signed. Permits are typically not required for gutter replacement alone in Garland, though we pull them when the scope calls for structural or drainage work.
See the difference
Before
After
Before
After
Before
AfterWhat Garland Homes Specifically Do to This Job
Garland’s building stock splits by era, and we bid differently depending on which one we’re standing in front of. The 1950s and 1960s single-story brick ranches in ZIPs 75040, 75041, and 75042 near the old downtown frequently have original fascia that’s been quietly softening for decades, plus downspouts that dumped water straight into the clay right at the slab. That’s how you get the foundation movement so many of these homes live with. Newer subdivisions out toward 75043 and 75044 are two-story brick-and-frame with steeper roofs and more footage, and those jobs run higher. The Blackland Prairie clay underneath all of it swells in spring and shrinks hard in summer, so where the water lands matters as much as how much the gutter holds. Hail and high wind are routine here, which is why we don’t recommend light-gauge panels on the north and west faces. And because Garland still runs its own permitting and inspections rather than deferring to Dallas County, we know the code we’re building to the moment we walk the property.
Serving Garland, TX – Our Local Coverage Area
We serve Garland and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked: Gutters & Accessories in Garland

Most Garland gutter jobs are finished in a single day, from removal through water test. Two-story homes with complex rooflines or homes that need fascia repair typically take two days. You’ll know the timeline from the written estimate before any work starts.
No permit is required for a straight gutter replacement in Garland. Permits come into play when the scope includes structural repair, re-routing drainage, or work tied to a larger roofing project. When a permit is needed, we pull it and coordinate the inspection.
Yes. Standard gutter replacement fastens to the fascia and drip edge and doesn’t require roof removal or structural changes. If we find rot in the fascia board, we’ll tell you and quote the repair as a separate line item before any work begins.
Steel gutters and premium leaf guards run $2,000 to $5,500 on a typical Garland home, more than aluminum but with better hail resistance and fewer replacements over twenty years. If you’re already replacing a roof or planning a full gutter line, it’s worth pricing. Call (888) 426-8078 and we’ll quote both grades side by side.
Every gutter installation we complete is covered under our 730-Day Done Right Promise: if the work isn’t right, we make it right. Standard material warranties from manufacturers apply on top of that. Ask for the details in writing when we’re on site.
Homeowners often pair gutter work with other projects we run in Garland, like Sliding & Patio Doors in Garland, Impact Garage Doors in Garland, or a full Roofing replacement. We handle all three in-house, so one contractor coordinates the whole scope. Our teams cover Garland and the surrounding areas including Sachse, Rowlett, Wylie, and Sunnyvale.
Get a Free Gutters & Accessories Estimate in Garland
Call (888) 426-8078 to schedule a free on-site estimate for Gutters & Accessories in Garland. A live person answers 24/7, no voicemail, and we’ll confirm a time that fits your schedule. On the visit, we measure every run, inspect the fascia, and leave you with a written line-item quote, fixed pricing, and a clear timeline. If you want to talk through options first, ask us about colors, guards, and drainage in the same call.
Written by the team at Groundwork Construction Co.












